冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-常見問題-叉車秤的故障分析及解決方案!

叉車秤的故障分析及解決方案!

來源:http://nukkadh.com/ 日期:2019-05-31 發布人:admin

  故障1:叉車秤稱重多次,但重量不一致,存在誤差。

  Fault 1: Forklift scale weighs many times, but the weight is not the same, there are errors.
  解決方案1:將叉車秤提升到zui的高度,在秤與叉車蓋之間插入一張紙,做一個圓圈,看是否有可以依靠的地方。如果有問題,可以使用適當的工具傾斜
  Solution 1: Raise the forklift scale to the height of zui, insert a piece of paper between the scale and the cover of the forklift, and make a circle to see if there is any place to rely on. If there is a problem, you can use the appropriate tool tilt
  解決方案2:抬起齒輪蓋,松開傳感器彈簧,用一字螺絲刀調整,然后安裝彈簧。如果傳感器上沒有調節螺絲,松開夾緊彈簧,取下齒輪蓋,然后將蓋上的4顆螺絲按2-3圈擰緊。
  Solution 2: Lift the gear cover, loosen the sensor spring, adjust it with a screwdriver, and install the spring. If there is no adjusting screw on the sensor, loosen the clamping spring, remove the gear cover, and then tighten the four screws on the cover by 2-3 turns.
  故障2:叉車稱重時跳數不歸零
  Fault 2: The number of hops does not return to zero when forklift truck weighs
  解決方案:首先,如果發現秤重不準確的問題,即一件秤在兩種稱重狀態下都是一樣的,需要重新校準和調整,直到秤重準確為止。如果跳數不為零的錯誤引起的,請檢查傳感器固定螺絲是否松動,是否在一個平面上,如沒有螺絲松了,在一個平面上,然后需要檢查傳感器是否本身是有問題的(傳感器本身檢測:停止使用萬用表測試的四個傳感器,無論是線性),如果傳感器本身有問題,需要更換傳感器。
濟南二手叉車
  Solution: First of all, if the problem of inaccurate weighing is found, that is, a scale is the same in both weighing states, it needs to be re-calibrated and adjusted until the scale is accurate. If the number of hops is not zero, please check whether the fixed screw of the sensor is loose, whether it is on a plane, if no screw is loose, on a plane, then you need to check whether the sensor itself is problematic (sensor itself detection: stop using the four sensors tested by the multimeter, whether linear), if the sensor itself has problems, you need to replace the sensor.
  缺點三:叉車秤對稱重不響應,經常出現誤差問題。
  The third disadvantage is that the symmetrical weight of forklift scale does not respond, and error problems often occur.
  解決方案:遇到此問題時,首先檢查線路是否有問題,接線頭是否短路,接線盒內線是否脫落等。其次,檢查儀器是否能正常開機,并進行自檢。如果電路有任何問題,請連接線路。如果儀器有任何問題,請與制造商/經銷商聯系。
  Solution: When encountering this problem, first check whether there is a problem in the line, whether the junction head is short-circuit, whether the inner line of the junction box falls off, etc. Secondly, check whether the instrument can be turned on normally, and self-check. If there is any problem with the circuit, please connect the line. If there is any problem with the instrument, please contact the manufacturer/distributor.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场