冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-常見問題-叉車叉取貨物的正確操作步驟!

叉車叉取貨物的正確操作步驟!

來源:http://nukkadh.com/ 日期:2019-07-19 發布人:admin

  叉車準備前叉取貨:需要調整叉臂間距。如果叉距過窄,貨物很容易失去平衡,翻倒;如果叉距過寬,貨物不易交叉或破碎。選擇正確的叉形方向。

  Forklift truck ready fork pick-up: need to adjust the spacing of fork arm. If the fork spacing is too narrow, the goods are easy to lose balance and overturn; if the fork spacing is too wide, the goods are not easy to cross or break. Choose the correct fork direction.
  步是慢慢接近要叉車的貨物,輕輕地剎車,使叉車停在貨物前面。
  The first step is to approach the forklift slowly and brake gently so that the forklift stops in front of the goods.
  第二,將叉車的叉臂抬起到適當的高度,調整叉車的叉臂與地面平行。
  Secondly, raise the forklift arm of the forklift truck to a proper height and adjust the forklift arm of the forklift truck to be parallel to the ground.
  第三步,慢慢啟動叉車,直到叉車臂完全進入叉車。此時,叉臂應與托盤平行,不要與托盤摩擦。
  The third step is to start the forklift slowly until the forklift arm fully enters the forklift. At this time, the fork arm should be parallel to the tray, not friction with the tray.
  第四,將貨物抬起5-10厘米,檢查貨物的穩定性和分布是否均勻,防止貨物翻滾。
  Fourthly, lift the cargo 5-10 cm to check the stability and distribution of the cargo, and prevent the cargo from rolling over.
濟南二手叉車
  第五步:放慢速度,直到貨物完全移開,否則不要側移或轉彎。
  Step 5: Slow down until the goods are completely removed, otherwise do not move sideways or turn.
  第六步:將貨物靠在叉臂的后柵欄上,將叉臂舉到離地15-20厘米的高度,在轉向叉之前盡量傾斜門臂。
  Step 6: Place the cargo on the back fence of the fork arm, lift the fork arm 15-20 cm above the ground, and tilt the door arm as far as possible before turning the fork.
  取貨時注意叉車:叉車抬起叉臂時,叉車應保持靜止,除非正在調整位置;當貨物被提升到較高的位置時,不要隨意移動、旋轉和傾斜叉臂,否則叉車可能翻倒。如貨物可能落在天篷上,切勿堆放。
  When picking up goods, pay attention to forklift trucks: forklift trucks should remain stationary when lifting the forklift arm, unless the position is being adjusted; when goods are lifted to a higher position, do not move, rotate and tilt the forklift arm at will, otherwise the forklift truck may overturn. If the goods may fall on the canopy, do not pile them up.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场