冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-常見問題-叉車廠家告訴您叉車是什么?

叉車廠家告訴您叉車是什么?

來源:http://nukkadh.com/冷门赚钱行业 日期:2019-01-07 發布人:admin

叉車是指對成件托盤貨品進行裝卸、堆垛和短間隔運輸作業的各種輪式轉移車輛。國際規范化組織ISO/TC110稱為工業車輛。屬于 物料轉移機械 。廣泛應用于車站、港口、機場、工廠、倉庫等國民經濟各部門,是機械化裝卸、堆垛和短間隔運輸的高效設備。

  Forklift truck is a kind of wheeled transfer vehicle which carries out loading and unloading, stacking and short-interval transportation of parts pallet goods. ISO/TC110, an international standardization organization, is called industrial vehicle. It belongs to material transfer machinery. It is widely used in stations, ports, airports, factories, warehouses and other departments of the national economy. It is an efficient equipment for mechanized loading and unloading, stacking and short-distance transportation.
  自行式叉車出現于1917年。第二次世界大戰期間,叉車得到發展。中國從20世紀50年代初開始制造叉車。叉車按結構分類有:平衡重叉車、前移叉車、側面叉車、插腿叉車、跨車和特種叉車6類。其中平衡重叉車應用廣,常簡稱為叉車。叉車轉移的目標大多是成件物品。將貨叉換裝各種用具(叉車屬具)后,又可轉移多種貨品。
  Self-propelled forklift truck appeared in 1917. During the Second World War, forklift trucks were developed. Forklift trucks have been manufactured in China since the early 1950s. Forklift trucks are classified by structure into six categories: balanced forklift truck, forward forklift truck, side forklift truck, legged forklift truck, crossing truck and special forklift truck. The balance weight forklift truck is the most widely used, often referred to as forklift truck. Forklift truck transfer is mostly aimed at finished goods. When forks are replaced with various appliances (forklift fittings), a variety of goods can be transferred.
  叉車主要由以下幾種設備組成:
  Forklift truck mainly consists of the following equipment:
  ①動力設備。如內燃機和蓄電池-電動機等。
  Power equipment. Such as internal combustion engine and battery-motor.
  ②傳動設備。分為機械、液力和液壓傳動設備。
  (2) Driving equipment. It is divided into mechanical, hydraulic and hydraulic transmission equipment.
  ③轉向設備。如轉向器、轉向輪、轉向拉桿等。
  (3) Steering equipment. Such as steering gear, steering wheel, steering tie rod, etc.
  ④工作設備。又稱門架,由內門架、外門架、貨叉架、貨叉、鏈輪、鏈條、起升油缸和歪斜油缸等組成。
  (4) Working equipment. Also known as portal frame, by the internal portal frame, external portal frame, fork rack, fork, sprocket, chain, lifting cylinder and skew cylinder and other components.
  ⑤液壓體系和制動設備。表明叉車功能的主要參數是在規范起升高度和規范載荷中心距下的額定起重量。載荷中心距是貨品重心到貨叉筆直段前壁的間隔。
  (5) Hydraulic system and braking equipment. It shows that the main parameters of forklift function are rated lifting weight under standard lifting height and standard load center distance. The load center distance is the distance between the center of gravity of the goods and the front wall of the straight section of the fork.
濟南二手叉車
  電瓶叉車使用注意事項
  Points for Attention in Use of Battery Forklift Truck
  1、 初次試車時要將車輪抬起,這樣即便有銜接錯誤,也不會發生風險。
  1. Raise the wheels during the first test run, so that there will be no risk even if there are connection errors.
  2、 電瓶充電時,必須將充電回路與斬波器完全脫離,由于除了影響充電機充電外,充電機發生的過電壓也 會危害斬波器。
  2. When the battery is charged, the charging circuit must be completely separated from the chopper, because in addition to affecting the charging of the charger, the overvoltage of the charger will also endanger the chopper.
  3、 要特別注意電瓶到電控的走線應平行布置并且要盡量短。
  3. Special attention should be paid to the parallel arrangement of battery to electronic control and the shortest possible route.
  4、 車輛在工況惡劣、通風困難的場所作業時,主張對控制器實施強制通風。 什么叫叉車大起重量和載荷中心?它們的聯系怎么? 貨品重心與載荷中心處于同一鉛垂線時,叉車所能裝卸貨品的大重量,稱為叉車的大起重量;規范載荷重心到貨叉筆直段前壁的水平間隔稱為叉車的載荷中心。通常載荷中心是按規范在設計時規則的亦即不同起重量的叉車一般情況下載荷中心是不同的。當貨品的重心在載荷中心規模內地,叉車能以大起重量進行裝卸作業,否則叉車的穩定性會遭到損壞而易發生事端。
  4. When a vehicle is working in a place with bad working conditions and difficult ventilation, it advocates forced ventilation for the controller. What is the maximum lifting weight and load center of forklift truck? How are they connected? When the center of gravity and the center of load are in the same vertical line, the maximum weight of the forklift truck can load and unload goods is called the maximum lifting weight of the forklift truck. The horizontal interval between the standard center of gravity and the front wall of the straight section of the forklift truck is called the load center of the forklift truck. Usually the load center is designed according to the rules of the code, that is to say, the load center of forklift trucks with different lifting weights is different in general. When the center of gravity of the goods is in the inland of the load center scale, the forklift truck can carry out loading and unloading operation with the maximum lifting weight, otherwise the stability of the forklift truck will be damaged and easy to happen.
  以上內容由濟南二手叉車整理發布,更多相關資訊可以點擊我們的官網進項咨詢:http://nukkadh.com
  The above contents are arranged and published by Jinan used forklift truck. For more information, please click on our official website for input consultation: http://nukkadh.com.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场