冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-常見問題-濟南叉車保養規則有哪些?

濟南叉車保養規則有哪些?

來源:http://nukkadh.com/ 日期:2019-03-27 發布人:admin

為了使叉車日常操作正常牢靠,必需堅持預防為主的準繩將叉車頤養制度化、標準化、科學化,因而設備管理人員要制定叉車頤養的規則做到定期定點的對叉車停止必要的頤養工作以進步叉車的運用效率。叉車租賃以為詳細頤養規則內容可參考如下:

  In order to make the daily operation of forklift trucks normal and reliable, it is necessary to adhere to the prevention-oriented criterion to institutionalize, standardize and scientifically make forklift maintenance rules, so that equipment managers can stop the necessary maintenance work of forklift trucks at regular fixed points to improve the efficiency of forklift operation. Forklift truck rental rules for detailed accommodation can be referred to as follows:
  叉車的頤養分為四類,即日常頤養,一級頤養,二級頤養
  Forklift accommodation can be divided into four categories: daily accommodation, first-class accommodation and second-class accommodation.
  1、日常維護,每班工作后。
  1. Daily maintenance after each shift.
  2、一級技術頤養,發起機累計運轉150小時后,每年工作時間缺乏150小時的內燃叉車每年停止一次一級頤養。
  2. First-class technical self-care. After the cumulative operation of the engine for 150 hours, the internal combustion forklift truck, which lacks 150 hours of working time per year, stops the first-class self-care once a year.
  3、二級技術頤養,發起機累計運轉450小時后,每三年工作時間缺乏450小時的內燃叉車,每三年停止一次二級頤養。
  3. Secondary technology self-sufficiency. After 450 hours of cumulative operation of the engine, the internal combustion forklift truck lacks 450 hours of working time every three years. Secondary self-sufficiency is stopped every three years.
  一、 日常維護
  I. Daily Maintenance
  1、 清洗叉車上污垢、泥土和垢埃,重點部位是:貨叉架及門架滑道、發電機及起動器、蓄電池電極叉柱、水箱、空氣濾清器。
  1. Clean the dirt, soil and dirt on forklift truck. The key parts are: forklift rack and gantry slideway, generator and starter, battery electrode fork column, water tank and air filter.
  2、 檢查各部位的緊固狀況,重點是:貨叉架支承、起重鏈拉緊螺絲、車輪螺釘、車輪固定銷、制動器、轉向器螺釘。
  2. Check the tightening condition of each part. The key points are: forklift support, lifting chain tension screw, wheel screw, wheel pin, brake, steering screw.
  3、 檢查轉向器的牢靠性、靈敏性。
  3. Check the reliability and sensitivity of steering gear.
  4、 檢查滲漏狀況,重點是:各管接頭、柴油箱、機油箱、制動泵、升降油缸、傾斜油缸、水箱、水泵、發起機油底殼、變矩器、變速器、驅動橋、主減速器、液壓轉向器、轉向油缸。
  4. Check the leakage situation. The key points are: pipe fittings, diesel tanks, oil tanks, brake pumps, lifting cylinders, inclined cylinders, water tanks, water pumps, engine oil pan, torque converter, transmission, drive axle, main reducer, hydraulic steering gear, steering cylinder.
  5、輪胎氣壓檢查:缺乏應補充至規則值,確認不漏氣。檢查輪胎接空中和側面有無破損,輪輞能否變形。
  5. Tire Pressure Inspection: Lack should be added to the regular value to confirm no leakage. Check whether the tire is damaged in the air and side, and whether the rim can be deformed.
濟南叉車租賃
  6、制動液、水量檢查:查看制動液能否在刻度范圍內,并檢查制動管路內能否混入空氣。添加制動液時,避免灰塵、水混入。在向叉車水箱加水時,就運用清潔自來水,若運用了防凍液,應加注同樣的防凍液。水溫高于70℃時,不要翻開水箱蓋,翻開蓋子時,墊一塊薄布,不要帶手套擰水箱蓋。
  6. Inspection of brake fluid and water quantity: check whether brake fluid can be within the scale range, and check whether air can be mixed into the brake pipeline. When adding brake fluid, avoid mixing dust and water. When adding water to forklift truck water tank, clean tap water is used. If antifreeze is used, the same antifreeze should be injected. When the water temperature is higher than 70 C, do not open the lid of the water tank. When opening the lid, pad a thin cloth. Do not twist the lid of the water tank with gloves.
  7、發起機機油量、液壓油、電解液檢查:先拔出機油標尺,擦凈尺頭后插入再拉出檢查油位能否在兩刻度線之間。工作油箱內油位應在兩根刻度線之間;油太少,管路中會混入空氣,太多會從蓋板溢出。電瓶電解液也同樣要處在上下刻度線之間,缺乏則要加蒸餾水到頂線。
  7. Inspection of engine oil quantity, hydraulic oil and electrolyte: first pull out the oil gauge, wipe off the ruler head, then insert and pull out to check whether the oil level can be between the two calibration lines. The oil level in the working tank should be between the two calibration lines; too little oil will mix with air in the pipeline and too much will spill over from the cover plate. Battery electrolyte should also be between the upper and lower scale lines, and distilled water should be added to the top line for lack.
  8、制動踏板、微動踏板、離合器踏板、手制動檢查:踩下各踏板,檢查能否有異常愚鈍或卡阻。手制入手柄的作用力應小于300N,確認手制動平安牢靠。
  8. Brake pedal, fretting pedal, clutch pedal, hand brake check: step on each pedal, check whether there is abnormal dullness or obstruction. The force of the hand brake should be less than 300N to ensure that the hand brake is safe and reliable.
  9、皮帶、喇叭、燈光、儀表等檢查:檢查皮帶松緊度能否契合規則,沒有調整余量或破損有裂紋,須改換;喇叭、燈光、儀表均應正常有效。
  9. Inspection of belt, horn, lamp, instrument, etc. Check whether the belt tightness conforms to the rules. If there is no adjustment allowance or cracks in the damaged belt, it should be replaced. The horn, lamp and instrument should be normal and effective.
  10、 放去機油濾清器沉淀物。
  10. Remove the oil filter sediment.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
冷门赚钱行业 網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场