冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-新聞動態-叉車更換輪胎的過程操作方法!

叉車更換輪胎的過程操作方法!

來源:http://nukkadh.com/ 日期:2019-04-26 發布人:admin

山東電動叉車在長時間的運輸過程中,其輪胎是容易受到磨損的位置。當輪胎出現過度磨損導致設備不能夠正常運行的時候,就需要我們對其進行一定的更換工作。那么在進行更換的過程中應該要怎么操作呢?

  The tire of Shandong electric forklift truck is the most vulnerable to wear and tear in the long transportation process. When the tire wears excessively and the equipment can not run normally, we need to replace it. So what should be done in the process of replacement?
  1、卸下電動叉車的載荷并將車輛停放在平坦、硬實的路面上,貨叉下降到地面,施加停車制動止住車輪。
  1. Unload the load of the electric forklift and park the vehicle on a flat and hard road surface. The fork drops to the ground and applies parking brake to stop the wheel.
  2、用千斤頂頂在所要更換輪胎的那一側的外側門架下面。把叉車頂起到輪胎依然稍稍與地面接觸的程度。在叉車機架前側下面放置墊塊,以防止下落。
  2. Use jack under the outside door frame on the side where the tire is to be replaced. Put the top of the forklift truck up to the point where the tire still touches the ground slightly. Place pads under the front side of forklift frame to prevent falling.
  3、用輪轂螺母扳手或其它工具松開輪轂螺母,直到螺母可用手轉動。松開螺母的順序應按對角線的順序進行。
  3. Use hub nut wrench or other tools to loosen hub nut until the nut can be rotated by hand. The sequence of loosening nuts should be in diagonal order.
  4、把電動叉車再頂起一點,直到輪胎稍稍離地。拆下輪轂螺母并拆下前輪組件。
  4. Push up the electric forklift a little more until the tire is slightly off the ground. Remove hub nut and front wheel assembly.
  5、把前輪組件的輪轂的那一側放置在平坦、硬實的路面上,路面上應鋪木板或毛毯等防止輪輞檫傷的墊子,借助工具,壓下輪胎,取下兩片半片式卡簧,再取下擋圈,就可拆下輪胎。
  5. Place the hub side of the front wheel assembly on a flat and hard road surface. Pavement should be paved with wooden boards or blankets and other cushions to prevent the rim from galling. With the help of tools, press down the tire, remove two half-leaf clips, and then remove the retaining ring, the tire can be removed.
  6、把新輪胎放進輪輞(注意輪胎的方向),壓下輪胎,安放好擋圈,再插裝好卡簧,松開輪胎,就裝配好了前輪組件。
濟南二手叉車
  6. Put the new tire into the rim (pay attention to the direction of the tire), press down the tire, place the retaining ring, insert the clip spring, loosen the tire, and assemble the front wheel assembly.
  7、把裝配好的前輪組件,套進輪轂螺栓,先用手逐個擰緊輪轂螺母,再用輪轂螺母扳手或其它工具對角地預緊輪轂螺母,預緊力矩20-30Nm(2-3.5kgfm)。注意螺栓和螺母的螺紋上不得沾有油脂和機油,否則會影響螺母的緊固力矩,造成意外安全事故。
  7. Insert the assembled front wheel assembly into the hub bolts, tighten the hub nuts one by one by hand, then pre-tighten the hub nuts diagonally with the hub nut wrench or other tools, and the pre-tightening moment is 20-30Nm (2-3.5kgfm). Attention should be paid to the thread of bolts and nuts not to be contaminated with grease and oil, otherwise it will affect the fastening moment of nuts and cause accidents.
  另外值得我們注意的是在電動叉車完成對輪胎的更換工作之后,需要及時對車輛進行試運轉工作。并及時檢查輪胎螺母是否存在有松動的現象,如果存在問題的話可以根據需要及時將其擰緊,在確保車輛無任何故障問題之后才可以進行正常的運輸工作。
  In addition, it is worth noting that after the electric forklift completes the tire replacement work, it is necessary to carry out the trial operation of the vehicle in time. And timely check whether there is loosening phenomenon of tire nuts, if there is a problem, it can be tightened in time according to need, in order to ensure that there is no trouble in the vehicle before normal transportation work.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
冷门赚钱行业 網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场