冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-新聞動態-叉車轉向節的檢驗與修理規范!

叉車轉向節的檢驗與修理規范!

來源:http://nukkadh.com/冷门赚钱行业 日期:2019-05-22 發布人:admin

  叉車轉向節配件作用主要是當叉車在程度路面行駛時,叉車輪子以程度軸為中心下下擺動,可減輕車架的改變,保證每一個叉車輪子的負荷平均,同時也保證叉車行駛穩定。下面是叉車各個轉向節配件的檢驗與修理規范。

  Forklift steering knuckle fittings are mainly used when the forklift truck is running on the level road surface, the forklift wheels swing downward and downward with the degree axis as the center, which can reduce the change of the frame, ensure the average load of each forklift wheel, and also ensure the stability of the forklift truck. The following are the inspection and repair specifications for each steering knuckle fittings of forklift trucks.
  一、 當叉車轉向節的頸部有裂紋時,應該給予改換。
  1. When there is a crack in the neck of the steering knuckle of forklift truck, it should be replaced.
  二、 叉車轉向節配件之軸承E及油封軸頸F的磨損,普通應不大于0.05mm,當大于此值時可用鍍鉻辦法修復。
  2. The wear of bearing E and oil seal Journal F of steering knuckle fittings of forklift truck should not be more than 0.05 mm in general. When it is greater than this value, it can be repaired by chromium plating.
  三、 轉向節推力軸承平面,應該平整,如不平整時應修平。
  3. The plane of thrust bearing of steering knuckle should be flat, if uneven, it should be trimmed.
  四、 叉車轉向節配件螺紋如損傷超越2牙時,可修車螺紋配螺母,或堆焊后重新車削螺紋。
  4. Forklift steering knuckle fittings threads can be repaired with nuts or re-turned after surfacing if the damage exceeds 2 teeth.
濟南二手叉車
  五、 叉車轉向節的裝配與調整。轉向節和轉向節銷軸的間隙應不大于0.1mm。
  Fifth, assembly and adjustment of forklift steering knuckle. The clearance between the steering knuckle and the pin shaft of the steering knuckle shall not exceed 0.1 mm.
  六、 轉向節與轉向橋間的端隙普通為0.05-0.1mm。如端隙過大,可加裝調整墊圈停止調整。
  6. The end clearance between steering knuckle and steering bridge is usually 0.05-0.1 mm. If the end clearance is too large, adjusting washer can be installed to stop adjusting.
  七、 轉向節軸與轉向橋的滾針軸承,其大間隙應不大于0.1mm。
  7. The maximum clearance of needle roller bearings for steering knuckle axles and steering axles shall not exceed 0.1 mm.
  八、 轉向節銷孔誤差為0.06mm,當大于0.1mm時,可鉸孔至修理尺寸,配主銷軸。
  8. The pin hole error of steering knuckle is 0.06mm. When the pin hole error is greater than 0.1mm, the pin hole can be reamed to repair size, and the main pin shaft can be matched.
  九、 當轉向板銷孔磨損時,不得大于0.15mm,否則可鉸至修理尺寸,配主銷軸。
  9. When the pin hole of the steering plate is worn out, it must not be greater than 0.15mm, otherwise it can be reamed to the repairing size and fitted with the main pin shaft.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场