冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-新聞動態-叉車轉向沉重的故障原因是什么?

叉車轉向沉重的故障原因是什么?

來源:http://nukkadh.com/ 日期:2019-12-31 發布人:admin

  很多用戶對電動叉車廠家的反應是:在使用中,偶爾會遇到重轉向叉車的現象,那么這種故障現象的原因是什么呢?綜上所述,主要有以下原因。

  The response of many users to the electric forklift manufacturers is: in use, they occasionally encounter the phenomenon of heavy turning forklift, so what is the cause of this failure? In summary, there are mainly the following reasons.
  1. 水平拉桿、轉向橋彎曲變形或電動叉車胎壓不足。
  1. The horizontal pull rod and steering axle are bent or deformed or the tire pressure of electric forklift is insufficient.
  2. 水平直拉桿的球頭裝置太緊,需要松開。
  2. The ball head device of the horizontal straight rod is too tight and needs to be loosened.
  3.電動叉車轉向螺桿上下軸承調整過緊,或叉車軸承損壞。
  3. The upper and lower bearings of the steering screw of the electric forklift are adjusted too tightly, or the bearings of the forklift are damaged.
  4、轉向器潤滑不好,如:需要在轉向器上加油。球頭未及時潤滑,工作時摩擦阻力增大。將方向盤向下轉動,若感到放松,則表示轉向機內部潤滑良好,然后檢查傳動機構是否太緊,而傳動機構潤滑不良,發現問題及時調整,潤滑。
  4. The steering gear is not well lubricated, for example, oil needs to be added to the steering gear. The friction resistance increases when the ball head is not lubricated in time. Turn the steering wheel downward. If you feel relaxed, it means that the internal lubrication of the steering gear is good. Then check whether the transmission mechanism is too tight, and the transmission mechanism is not well lubricated. If you find any problem, adjust it in time and lubricate it.
濟南二手叉車
  電動叉車齒條與齒扇嚙合間隙調整過緊。對于故障診斷和放電,拆卸舵機搖臂。如果方向盤轉動后感覺沉重,調整齒條、齒扇、螺桿軸承的行程。如果您覺得松緊不均或卡在里面,檢查螺絲、鋼球、管夾、齒條和軸承是否有粗糙度或損壞。如有必要,建議直接修理或更換。
  The meshing clearance between the rack and the gear sector of the electric forklift is adjusted too tight. For troubleshooting and discharging, remove the steering gear rocker arm. If the steering wheel feels heavy after turning, adjust the stroke of rack, gear sector and screw bearing. If you feel that the tightness is uneven or stuck in, check the screw, steel ball, pipe clamp, rack and bearing for roughness or damage. If necessary, direct repair or replacement is recommended.
  以上就是電動叉車廠家共享叉車轉向重的原因。建議在遇到叉車重轉向問題時,從以上幾個方面著手,逐一檢查,及時解決。
  The above is the reason why the electric forklift manufacturers share the forklift turning weight. It is suggested to check one by one from the above aspects and solve the problem in time.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场