全国服务热线:15953195999
产品中心
您所在的位置:首页-新闻中心-新闻动态-济南二手叉车传动装置及毛病扫除

济南二手叉车传动装置及毛病扫除

来源:/ 日期:2018-10-13 发布人:admin

济南二手叉车传动装置及毛病扫除

Ji'nan used forklift transmission and trouble shooting
在查看叉车前的操作,应先添加满足的油,使油面坚持最小的油量。润滑油有必要避免油进入油中,由于水分蒸腾简单发生气泡,从而下降发动机的功率和损坏密封。二手叉车的设备是由一个力和一个齿轮泵组成的。一般用压缩空气来驱动齿轮啮合,输出功率时,当装置被安装在动力开关的驱动力时,如液压泵发现驱动轴的驱动力不滚动,宣布反常声响,其毛病原因一般是:使用了二手装载机的空气压力。
Before looking at the operation of the fork lift truck, we should first add the oil to meet the minimum oil content. Lubricating oil is necessary to avoid oil entering the oil, because water transpiration occurs simply bubble, thereby reducing the power of the engine and damaging the seal. The equipment of used forklift truck is made up of a force and a gear pump. Compressed air is generally used to drive gears meshing, output power, when the device is installed in the power switch drive force, such as hydraulic pump found that the drive shaft does not roll, announce abnormal sound, the main reason is generally: the use of second-hand loader air pressure.
查看办法:首要调查压力表上的压力,假如压力低于工作压力,它是添加油门来改进空气压力;假如压力是正常的,你有必要找出是否有空气走漏的电磁阀前和后的降雨时节,管道走漏,导致空气走漏量。查看电磁阀是否安全可靠。假如毛病扫除,拆下力缸,拆下活塞杆,替换活塞或O型密封圈,并拆下气缸壁。
Check method: First investigate the pressure on the pressure gauge, if the pressure is lower than the working pressure, it is to add throttle to improve air pressure; if the pressure is normal, you need to find out whether there is air leakage solenoid valve before and after the rainy season, pipeline leakage, resulting in air leakage. Check whether the solenoid valve is safe and reliable. If something goes wrong, remove the cylinder, remove the piston rod, replace the piston or O-ring, and remove the cylinder wall.
济南二手叉车
当完结作业结束时,封闭电源开关,堵截驱动轴的动力,使液压泵工作,一般有以下几个原因:紧压下的螺母松动;活塞杆的螺丝松动;采纳的活塞杆绷簧和性能削弱或损坏。消除法的二手辊:先查看一下,以按捺拨叉螺母掉落,假如螺母掉落,把力取缸座拆下,放上新的锁盘和紧固螺母。假如在活塞杆的杰出状态下,将力除掉,将气缸盖拆下,并拆下活塞杆的螺钉。假如螺丝松动,应从头紧固,穿上开口销。以上2个项目均完结无损坏,用手推的活塞杆,叉车配件证明已损坏,咱们有必要撤除缸体,替换新的绷簧。
When the end of the operation, close the power switch to block the drive shaft power, so that the hydraulic pump work, there are several reasons: tightly pressed nut loosening; piston rod screw loosening; adopted piston rod tension spring and performance weakening or damage. Elimination of the second-hand roller: first check to press the fork nut drop, if the nut drop, take the cylinder seat off the force, put a new lock and fastening nut. If in the outstanding state of the piston rod, remove the force, remove the cylinder head, and remove the piston rod screw. If the screw is loose, it should be fastened and put on the cotter pin. The above two items are all finished without damage. The piston rod and forklift truck fittings are proved to be damaged. It is necessary to remove the cylinder block and replace the new tension spring.
济南韩工机械设备有限公司,对济南二手叉车感兴趣的朋友可以关注我们,更多精彩内容知识敬请期待!
Jinan Han Gong Machinery Equipment Co., Ltd., Jinan used forklift truck interested in friends can pay attention to our , more exciting content knowledge please look forward to!!

  左右棋牌_左右棋牌官网www.nukkadh.com版权所有 2018济南韩工机械设备有限公司 All Rights Reserved
地址:济南市章丘区龙山街道向东3公里路北   电话:15953195999
网站:/   备案号:鲁ICP备14018186号-1  技术支持:济南诺商

 网站地图 XML TXT

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除!

www.nukkadh.com
友情链接:左右棋牌    左右棋牌游戏  左右棋牌APP  左右棋牌