冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-新聞動態-叉車故障的應急維修措施!

叉車故障的應急維修措施!

來源:http://nukkadh.com/冷门赚钱行业 日期:2018-12-03 發布人:admin

開叉車工作時難免出現一些故障,10個應急維修小技巧 ,臨時不求人。

  When driving a forklift truck, there are inevitably some faults. There are 10 emergency repair tips, which do not ask for help temporarily.
  1叉車油箱損傷
  1 forklift truck tank damage
  發現油箱漏油,將漏油處擦干凈,用肥皂或泡泡糖涂在漏油處,暫時堵塞;用環氧樹脂膠粘劑修補,效果更好。
  If oil leak is found, wipe the oil leak clean, apply soap or bubble sugar to the oil leak, temporarily plug it, and repair it with epoxy resin adhesive, the effect is better.
  2叉車油管破裂
  2 forklift tubing burst
  將破裂處擦干凈,涂上肥皂,用布條或膠布纏繞在油管破裂處,并用鐵絲捆緊,然后再涂上一層肥皂。
  Clean the rupture, apply soap, wrap cloth or tape around it, tie it with wire, and then coat it with soap.
  3叉車油管折斷
  3 forklift tubing fracture
  找一根與油管直徑適應的膠皮或塑料管套接。如套接不夠緊密,兩端再用鐵絲捆緊,防止漏油。
  Find a rubber or plastic pipe sleeve suitable for tubing diameter. If the socket is not tight enough, the two ends are tightened with wire to prevent oil leakage.
  4油管接頭漏油
  4 oil pipe joint leakage.
  發動機油管接頭漏油,多是油管喇叭口與油管螺母不密封所致。可用棉紗纏繞于喇叭下緣,再將油管螺母與油管接頭擰緊;還可將泡泡糖或麥芽糖嚼成糊狀,涂在油管螺母座口,待其干凝后起密封作用。也可將人造革或皮褲帶剪成型或放入孔中砸成型,安上即可,還可用一截塑料管剪開成型安上。
  Oil leakage of engine tubing joint is mostly caused by unsealing of tubing horn mouth and tubing nut. Cotton yarn can be used to wrap around the lower edge of the horn, then tighten the tubing nut and tubing joint. Bubble sugar or maltose can also be chewed into paste and coated on the socket of tubing nut, which can be sealed after drying and setting. Artificial leather or leather belt can also be cut into shape or smashed into holes, then installed, and a plastic pipe can be used to cut into shape and mounted.
  5沉淀杯破裂
  5 rupture of precipitating cup
  用膠布管或塑料管把沉淀杯進出油管套上,使油不經過沉淀杯直通。
  The precipitation cup is put into and out of the tubing sleeve with a rubber or plastic pipe, so that the oil does not pass through the precipitation cup directly.
  6風扇皮帶斷裂
  6 fan belt fracture
  可把斷了的皮帶用鐵絲串聯扎好或采用開開停停的辦法把車開走。
  The broken belt can be tied up in series with wire or the car can be driven away by stopping and starting.
  7螺孔滑扣
  7 screw hole slide fastener
  螺孔滑扣導致漏油或連桿松動,使其無法工作。這時可將原螺桿用錘子錘扁,使其兩邊膨脹增大(注意上面幾扣不要錘,以使入孔)再緊固好,但不可多次拆卸,待下次保養時修理。
  The screw hole slippage causes oil leakage or loosening of the connecting rod, which makes it unable to work. At this time, the original screw can be hammered flat with a hammer, so that both sides expand and increase (pay attention to the upper buttons do not hammer, so as to enter the hole) and then tighten, but can not be dismantled many times, to be repaired when the next maintenance.
濟南二手叉車
  8進、出水軟管破裂
  8. Rupture of inlet and outlet hoses
  破裂不大時,可用涂有一層肥皂的布將漏水處包扎好;如破裂較大時,可將軟管破裂處切斷,在中間套上一個竹管或鐵管,并用鐵絲捆緊。
  When the rupture is not large, the leak can be wrapped up with a soap-coated cloth; if the rupture is large, the rupture of the hose can be cut off, and a bamboo or iron pipe can be put in the middle, and tied with wire.
  9膜片或輸油泵膜片破裂或折斷
  9. Break or break of diaphragm or oil pump diaphragm
  可拆開油泵取出膜片,用膠木板、電工絕緣膠木或塑料布按原型狀尺寸鋸銼成型,并磨光裝上;或者將油管直接通到噴油泵上。
  The diaphragm can be removed from the oil pump, and the diaphragm can be sawn and filed according to the prototype size with bakelite board, electrical insulating bakelite or plastic cloth, and then polished. Or the oil pipe can be directly connected to the fuel injection pump.
  10叉車缸蓋等部位出現砂眼而漏油、漏水
  Oil and water leakage due to sand holes in cylinder head and other parts of forklift truck
  根據砂眼大小,選用相應規格的電工用保險絲,用手錘輕輕將其砸入砂眼內,即可去除漏油、漏水。
  According to the size of the sand holes, electrician fuses of corresponding specifications are selected and lightly smashed into the sand holes with a hammer to remove oil and water leakage.
  以上就是濟南二手叉車故障的十個應急措施,希望對您有所幫助,更多內容可以點擊咨詢:http://nukkadh.com
  These are the ten emergency measures for the second-hand forklift truck in Jinan. I hope they will be helpful to you. For more information, please click on http://nukkadh.com.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
冷门赚钱行业 網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场