冷门赚钱行业

全國服務熱線:15953195999
產品中心
您所在的位置:首頁-新聞中心-新聞動態-濟南叉車貨叉的檢修方法!

濟南叉車貨叉的檢修方法!

來源:http://nukkadh.com/ 日期:2019-02-09 發布人:admin

按標準規定、貨叉使用狀況應每年檢查一次;在惡劣工況條件下使用的叉車更需要頻繁地進行檢查,以查出任何缺陷或永久變形,采取有關技術措施,從而消除不安全隱患。叉車貨叉的檢驗應由技術人員進行,發現貨叉產生了有礙安全使用的跡象,失效和明顯變形等任何缺陷,必須停止使用,只有經過嚴格修復,并經測試驗收合格后方可使用。

According to the national standards, forklifts should be inspected once a year; forklifts used under harsh conditions need to be inspected frequently to detect any defects or permanent deformation, and take relevant technical measures to eliminate potential unsafe hazards. The inspection of forklift trucks and forks should be carried out by professional technicians. It is found that the forklift has any defects such as hindering safe use, failure and obvious deformation. It must be stopped using. It can only be used after strict repair and passing the test and acceptance.
貨叉表面裂紋(尤其貨叉根部、上鉤、下鉤及垂直段的連接處),一經發現,兩叉尖之間的高度差,超過水平段長度的3%,貨叉必須停止使用。使用中還必須保證定位銷在原位處于良好的維護和正常的工況,若發現任何故障,貨叉在進行良好的修復之前必須停止使用。應定期徹底檢查貨叉水平段和垂直段的磨損程度,尤其是貨叉根部,若其厚度減少至原來的90%也應停止使用。貨叉的上掛鉤支承面以及上下掛鉤的定位面的磨損、積壓及其它局部變形,致使貨叉和叉架之間的間隙增大,必須修復之后方可使用。
濟南二手叉車
Surface cracks of forks (especially at the joints of the roots, upper hooks, lower hooks and vertical sections) are found to be higher than 3% of the length of the horizontal section. Forks must be stopped. It is also necessary to ensure that the positioning pin is in good maintenance and normal working condition in situ. If any faults are found, the fork must be stopped before good repair. The wear degree of horizontal and vertical section of fork, especially the root of fork, should be checked thoroughly and regularly. If the thickness of fork is reduced to 90%, it should also be stopped using. The wear, overstock and other local deformations of the upper and lower hook supporting surfaces and the positioning surfaces of the upper and lower hooks of the fork increase the gap between the fork and the fork rack, which must be repaired before it can be used.
在沒有條件的情況下,貨叉斷損好更換新件、不允許湊合使用,即使貨叉焊修后,只有經過嚴格的技術標準檢驗,達到原廠規范要求之后,方可投入使用。
In the absence of conditions, fork breakage is best replaced with new parts, not allowed to make use of, even after the fork welding repair, only after strict technical standards inspection, to meet the requirements of the original plant specifications, can it be put into use.

版權所有 ? 2018濟南韓工機械設備有限公司 All Rights Reserved
地址:山東省濟南市章丘區龍山街道辦事處東3公里路北韓工叉車濟南4S店   電話:15953195999
冷门赚钱行业 網站:http://nukkadh.com/   備案號:魯ICP備14018186號-1  技術支持:

 

冷门赚钱行业【BENZHANTUPIANJUNYOUWANGZHANSUOYOUFANGTIGONG,BUFENTUPIANLAIYUANYUWANGLUO,RUWUYIZHONGQINFANLEMOUMEITIHUOGERENDEZHISHICHANQUAN,QINGLAIXINHUOLAIDIANGAOZHI,BENWANGZHANJIANGLIJISHANCHU。】

开心生肖 贵州11选5开奖结果 福建11选5走势图 广东11选5开奖结果 湖北11选5开奖结果 正规捕鱼游戏 正规捕鱼游戏 万丰国际赌场